Craftsman Leaf Blower / Vacuum Parts
YOUR TRUSTED CHOICE
- Genuine Brand Name Part
- Fast Delivery
- Expert Customer Support
Popular Craftsman Leaf Blower / Vacuum Parts
This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filter is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.
... Read more
Fixes these symptoms
- Engine stops after a few seconds or minutes
- Will Not Start
This is the replacement fuel line 25 Inch for several OPE products that use small engines. The fuel line carries fuel from the tank to the carburetor. Over time, the fuel line can become badly clogged, and it can become brittle as well. When the fuel line is badly clogged or cracked, fuel can leak out and it can make it difficult to start or run the engine. To replace the fuel line, carefully disconnect the old line from the carburetor and from the fuel grommet, then replace it with the new line. This fuel line is 25 inches in length and is made of clear plastic. The fuel line is sold individually and is an OEM part sourced directly from the manufacturer.
... Read more
Fixes these symptoms
- Engine stops after a few seconds or minutes
- Will Not Start
This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. The excess fuel is forced through the purge line back into the fuel tank. Over time the Tank Purge Line will become brittle and crack and will need to be replaced.
Fixes these symptoms
- Engine stops after a few seconds or minutes
- Will Not Start
A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below the Venturi is a butterfly valve called the throttle valve ' a rotating disc that can be turned end-on to the airflow, so as to hardly restrict the flow at all, or can be rotated so that it (almost) completely blocks the flow of air. This valve controls the flow of air through the carburetor throat and thus the quantity of air/fuel mixture the system will deliver, thereby regulating engine power and speed. The throttle is connected, usually through a cable or a mechanical linkage of rods and joints. Fuel is introduced into the air stream through small holes at the narrowest part of the Venturi and at other places where pressure will be lowered when not running on full throttle.
... Read more
Fixes these symptoms
- Engine stops after a few seconds or minutes
- Will Not Start
This is a genuine OEM replacement part designed for use with gas trimmers/blowers. The fuel line is what delivers the fuel from the fuel tank into the carburetor. When you press the primer bulb, it will purge all the air out of the carburetor and fill its chambers with fuel. The excess fuel is then forced back into the tank through the return line. Over time these lines will become brittle and may crack, and will have to be replaced. This item is made out of rubber and it is sold individually.
... Read more
Fixes these symptoms
- Will Not Start
This is a genuine OEM replacement part, it is sold individually. By pressing on the Purge Bulb, it will force fuel into the fuel line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in the fuel return line. Over time the primer will lose its elasticity or crack and need to be replaced. We have an article and video on
This is a manufacturer approved O-Ring designed for lawn and garden equipment. This is the O-Ring that provides an Air Tight seal between Carburetor and Cylinder Head. If doing maintenance on carburetor it is recommended to replace the O-Ring instead of re-using the old one. Over time rings and seals tend to dry out and would no longer provide proper seal compromising engines performance.
This is a genuine OEM sourced part which is specially made for use with Craftsman handheld lawn and garden equipment. Its purpose is to deliver electric current from the ignition system to the combustion chamber. It will ignite the air fuel mixture by the spark. Unfortunately, over time a spark plug can wear out or it may get damaged eventually requiring a replacement to ensure peak performance. Keep in mind this high-quality spark plug is made of durable materials and is sold individually. Please make sure to refer to the owners manual of your model for the correct location and application of this component.
... Read more
This is a genuine Husqvarna replacement part, it is sold individually. The purpose of this filter is to keep dirt and other small particles from entering the carburetor and engine and causing internal engine damage. Once this type of filter gets clogged or dirty it should be changed (Not Cleaned). This is to prevent restricted air flow and foreign matter from entering the engine.