Cub Cadet Trimmer Parts
YOUR TRUSTED CHOICE
- Genuine Brand Name Part
- Fast Delivery
- Expert Customer Support
Popular Cub Cadet Trimmer Parts
$14.95
In Stock
This OEM fuel tank assembly is made out of Plastic and it includes the fuel lines, fuel cap, and fuel filter. It is a common part in gas trimmers that is used to hold the fuel needed for the engine. It is very important to replace the fuel tank if it is cracked or damaged to avoid further damage or serious injuries. Make sure to drain the gas tank before starting a repair.
Fixes these symptoms
- Will Not Start
$37.95
In Stock
A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below the Venturi is a butterfly valve called the throttle valve ' a rotating disc that can be turned end-on to the airflow, so as to hardly restrict the flow at all, or can be rotated so that it (almost) completely blocks the flow of air. This valve controls the flow of air through the carburetor throat and thus the quantity of air/fuel mixture the system will deliver, thereby regulating engine power and speed. The throttle is connected, usually through a cable or a mechanical linkage of rods and joints. Fuel is introduced into the air stream through small holes at the narrowest part of the Venturi and at other places where pressure will be lowered when not running on full throttle.
... Read more
Fixes these symptoms
- Engine stops after a few seconds or minutes
- Will Not Start
$13.95
In Stock
Fixes these symptoms
- Cutting line does not come out
$22.95
On Order
This is an authentic part that is supplied directly from the original equipment manufacturer for Craftsman trimmers. The fuel tank houses the fuel used to power the machine. This part is made of hard plastic and is sold individually. The fuel cap and fuel lines are included in the assembly. For installation you will need a screw driver to remove and shrouds and covers.
Fixes these symptoms
- Will Not Start
$5.95
In Stock
This is a manufacturer approved O-Ring designed for lawn and garden equipment. This is the O-Ring that provides an Air Tight seal between Carburetor and Cylinder Head. If doing maintenance on carburetor it is recommended to replace the O-Ring instead of re-using the old one. Over time rings and seals tend to dry out and would no longer provide proper seal compromising engines performance.
$7.95
In Stock
This is a genuine OEM sourced part which is specially made for use with Craftsman handheld lawn and garden equipment. Its purpose is to deliver electric current from the ignition system to the combustion chamber. It will ignite the air fuel mixture by the spark. Unfortunately, over time a spark plug can wear out or it may get damaged eventually requiring a replacement to ensure peak performance. Keep in mind this high-quality spark plug is made of durable materials and is sold individually. Please make sure to refer to the owners manual of your model for the correct location and application of this component.
... Read more
$5.95
In Stock
This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with trimmers and blowers. The gasket is used to seal the connection between the carburetor and the air cleaner assembly. It is recommended to replace gaskets when servicing the motor to ensure proper seals when the parts are reassembled. This item is available as an individual replacement part.
$23.95
In Stock
This is a genuine part that is supplied by the original manufacturer for use with Craftsman trimmers. The fuel tank stores the gasoline used to power the trimmer. This part is made of plastic and is sold individually. The fuel cap and fuel lines are all included in this kit. For this repair, you will need a screwdriver to remove any panels or covers, a pair of needle nose pliers, and a socket wrench to aid you.
$5.95
In Stock
This authentic component is supplied directly from the original equipment manufacturer for use with MTD string trimmers. It is an identical replacement for a missing or a faulty glide cap that was installed on a new unit. The cap is secured on the bottom of the cutting head assembly, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality item is made of durable plastic and is sold individually.
... Read more
$24.95
In Stock