Cultivator Parts
YOUR TRUSTED CHOICE
- Genuine Brand Name Part
- Fast Delivery
- Expert Customer Support
Shop By Brand
View More
Popular Cultivator Parts
$6.25
In Stock
This is a genuine component which is specially designed for use with Poulan, Husqvarna, Weed Eater and Jonsered tillers. It is supplied directly from the original equipment manufacturer. This item provides a high-quality replacement for a missing or a faulty hardware that was installed on a new unit. The clevis pin is installed in order to protect your tiller. If the auger gets jammed or clogged, the pin is designed to snap at a certain point of pressure, so it will not damage any other part of the unit. Please make sure to refer to the appropriate diagrams of your model for the correct application of this part. Keep in mind this high-quality clevis pin is made of durable metal and is sold individually. Replacing it is a simple task that should only require pliers to remove the old and secure the new.
... Read more
$5.95
In Stock
This filter is an authentic OEM replacement part sourced directly from the manufacturer. It is commonly used in MTD and Troy-Bilt tillers and cultivators. This part filters the air entering the carburetor. Without a proper air filter, the machine may stop running. It should be replaced if it is worn or clogged beyond cleaning. It is sold individually, and a screwdriver is needed to replace it.
$5.95
In Stock
This is a genuine OEM replacement part, it is sold individually. This is part of the clamp assembly that holds the accessories for the tools listed below. It is 3/4" in diameter,beveled in the center,with a 1/4" bore.
$16.75
On Order
This genuine OEM replacement drive belt is designed for use with rotary lawn mowers and garden tillers, providing a reliable connection between the engine and the cutting or tilling mechanism. Made from high-quality, durable rubber, this belt is built to withstand regular outdoor use and is sold individually. Replacing the belt is a relatively simple task that requires only a screwdriver. To perform the repair, first disconnect the spark plug to ensure safety. Then, remove the belt cover to access the old belt. After removing the worn belt, install the new one in its place, secure the cover, and reconnect the spark plug. Always consult your equipment’s manual for model-specific guidance and safety precautions.
... Read more
$11.95
In Stock
This PEX press tool jaw insert is used inside a crimping tool to grip and compress PEX crimp rings during installation. It helps ensure accurate, secure crimps for reliable pipe connections. Replacing a worn or damaged insert restores proper crimping performance and consistent results.
$10.95
On Order
This is a genuine OEM replacement part, it is sold individually. The purpose of the Fuel Pick--Up Line with Filter is to provide fuel into the carburetor via the primer bulb. The filter is situated inside the fuel tank,with the fuel line extending through an existing hole in the fuel tank. It is then connected to the primer bulb which will purge the air out of the carburetor. By pressing the primmer bulb it will fill the carburetor with fuel, once it is full the excess fuel will be forced back into the tank through the fuel return line. Over time the fuel filter will be come clogged with debris and will have to be changed.
... Read more
$25.15
In Stock
This is an authentic manufacturer sourced replacement part that is specially designed for use with gas powered lawn and garden equipment. The purpose of this gasket is to provide an air-tight seal for the gearcase. Over time gaskets tend to get compressed and deteriorate eventually requiring replacement. Please note one durable composite material gasket is included per order.
$29.35
In Stock
This is an authentic OEM part from Husqvarna for use with Tillers. The throttle control assembly attaches to the handle and the carburetor to control the engine speed. The most common reason for replacing the throttle control assembly is if the throttle is unresponsive, stuck open (or closed), the throttle cable is rusted, broken or the throttle trigger handle is broken or cracked. This part is sold individually. Here is a list of tools that are needed to replace the throttle control assembly wire cutters, long-nosed pliers, wrench socket/ratchet set and a small screwdriver.
... Read more
$31.95
On Order
This is an authentic fuel tank assembly for a trimmer. This assembly includes the fuel tank, fuel lines, and a fuel cap. Please note that the tabs used to secure the tank are sold separately. Replacing this fuel tank assembly will solve a leaking fuel tank, deteriorated fuel lines, or a broken fuel cap. If your fuel tank is leaking, this assembly should solve the issue. Never run your equipment with a damaged fuel tank, as this is unsafe. Before making this repair, be sure to drain the gas tank.
... Read more
$7.95
On Order
The purpose of the 791-182352 Fuel Return Tube is to return the excess fuel back into the fuel tank, after the primer bulb has been pressed and has primed the carburetor to start. Over time the Fuel Return Line will become brittle and crack and will need to be replaced.