Milwaukee Drill Press Parts
YOUR TRUSTED CHOICE
- Genuine Brand Name Part
- Fast Delivery
- Expert Customer Support
Popular Milwaukee Drill Press Parts
$11.95
In Stock
Genuine Milwaukee replacement part. This brush is sold individually, 2 are needed for the tools shown below. It is always best to replace both brushes, even if only one is worn.Worn brushes frequently are the cause behind a motor running poorly.Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking.Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
... Read more
$9.95
In Stock
This is a Genuine OEM Brush Holder Assembly for some Milwaukee Drills. This Assembly includes: Metal Brush Holder, Brush with a Lead Wire and the Spring. This item is sold individually. Most brush replacement jobs will require the purchase of two of these brush assemblies. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement.
... Read more
$5.95
In Stock
This is a Genuine OEM Sourced replacement part used on Milwaukee Drill Press Stands. This item screws onto the Bar Handle and allows for a firm grip. This item is made out of Black Plastic and it is Sold Individually. No tools are required to replace.
$16.95
In Stock
This genuine manufacturer-sourced part is specially designed for use with Milwaukee equipment. It is an identical replacement for a missing or a faulty gib that was installed on a new unit, unfortunately, over time it will wear out and it may begin to crack eventually requiring a replacement. This high-quality component is made of durable metal and is sold individually, keep in mind the hardware to secure it is sold separately. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this gib.
... Read more
$6.95
In Stock
This carbon brush assembly is specially designed for Milwaukee drill press. It is a genuine part sourced directly from original manufacturer. Carbon brushes through friction will gradually wear away requiring replacement. It is advised to replace both brushes at the same type. Includes one (1) carbon brush with a lead wire and spring attached. Please note, the brush caps and brush holders are sold separately. You should need a screwdriver and pliers to complete this repair job. • First make sure the tool is unplugged • Remove the brush cap • Remove the old brush • Install the new brush • Reassemble and test the tool
... Read more
$36.95
In Stock
It is an OEM part that is specially made for use with Milwaukee large base dymorigs. This gasket is utilized to provide a tight seal for the base. Over time gaskets tend to wear out and may begin to crack causing leaks and eventually requiring a replacement. Note, this high-quality component is made of durable rubber material and is sold individually. Check the appropriate diagram for your model to ensure the exact location and the correct replacement procedure. No special tools should be needed to perform this repair.
... Read more
$20.95
In Stock
$81.95
In Stock
This keyed chuck has a 1/2 inch capacity with a 5/8 inch - 16 thread. Use with chuck key 48-66-3280 and key holder 48-66-4040. The metal construction provides heavy-duty durability while the keyed design ensures the bit retention needed for high-torque applications. It can be used on reversing drills of matching capacities and threaded spindles. If your drill's bit retention is suffering, the rotation feels stiff, or the chuck has seized up entirely, a new chuck should fix the problem.
... Read more
$25.95
In Stock
The wear pad is made out of metal. This part is an OEM from Milwaukee for use in large base dymorigs and small base dymorigs. This Item is available individually. A screwdriver might be needed during the installation process. It will require replacing if it becomes broken or worn down.