Milwaukee Hammer Drill Parts
YOUR TRUSTED CHOICE
- Genuine Brand Name Part
- Fast Delivery
- Expert Customer Support
Popular Milwaukee Hammer Drill Parts
$10.95
In Stock
This is a genuine brush set designed for use with Milwaukee rotary hammers. This assembly includes two (2) carbon brushes with lead wires attached. Please note brush holders are sold separately. Due to prolonged contact with an armature brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. To complete this repair you would need a screwdriver. • Make sure the unit is unplugged • Remove screws from the housing to gain access to the armature and brushes • Remove old brushes and secure the new ones in brush holders • Re-assemble and test the tool
... Read more
$56.95
In Stock
This is a 1/2-inch OEM keyless chuck for hammer drills, allowing users to swiftly change drill bits and attachments without requiring a chuck key. Due to the mechanical stresses it undergoes, the jaws of the chuck can break or wear significantly, resulting in a loss of grip or excessive play. If you encounter difficulty tightening or loosening the chuck jaws on your drill or notice wobbling during operation, replacement is necessary. To replace this chuck assembly, you will need a screwdriver or drill to remove the initial left-handed screw on the inside. To completely remove the chuck, it is recommended that you secure the drill in a vise or use the drill itself, along with an Allen key, to detach the main chuck assembly from the drill. Once the old chuck is removed, you can effortlessly install the new chuck along with its securing screw. Please note that this chuck assembly is sold individually and does not include any additional securing hardware that may be required.
... Read more
$11.95
In Stock
Genuine Milwaukee replacement part, this item is sold individually. This Chuck Key tightens the jaws of the 1/2 inch capacity Chucks on all the Drill models shown below. For convenience a Chuck Key Holder part number 48-66-4040 can be ordered. It is attached to the power cord then the Chuck Key is attached to it.
$5.95
In Stock
This cord protector is a genuine Milwaukee replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.
$16.95
In Stock
This OEM sourced replacement part is designed for Milwaukee drills/drivers. This assembly secures carbon brushes around the armature to provide stable contact. This assembly consists of: plastic holder ring, four (4) metal brush holders with springs and four (4) carbon brushes with lead wires attached. To replace this assembly you would need a screwdriver. • First remove screws holding the cover together • Carefully separate housing to gain access to armature and brush holder • Disconnect the wires • Remove the screws holding brush card assembly • Remove old brush holder and install the new assembly • Reassemble and test your tool
... Read more
$49.95
In Stock
This Milwaukee Quik-Lok® cord is a genuine OEM replacement part, it is sold individually.
This is a three wire grounded 8 foot cord for fast field replacement of a damaged cord.
Made of premium grade Hi-Flex wire the cord is quickly removed and attached to Milwaukee tools with the Quik-Lok® cord feature.
To change a damaged cord simply turn the collar at the top of the cord counter clockwise to loosen the nut and pull down on the cord to remove.
To re-attach a new cord, line up the pins in the end of the tool with the pin receptacles in the end of the cord, push together and turn the collar clockwise to lock in place.
The Cord has a 5-15P NEMA type plug.
... Read more
$6.95
In Stock
This is a genuine Milwaukee Collet for using bits with 1/8-inch arbors. Due to prolonged, heavy use a collet may need to be replaced. Use Collet Nut Wrench Part Number: 45-96-0400 to remove the Collet Nut Part #: 44-40-0770.
$20.95
In Stock
This Trigger switch has 4 internal terminals. This authentic Milwaukee replacement part is sold individually. rnrnSwitches are commonly replaced parts in power tools. A switch handles all on/off and variable speed functions. They also have a role in electric breaking; they can momentarily reverse electrical polarity. Because switches use mechanical internals, they tend to degrade and wear out over time, eventually requiring replacement. Some common signs of a broken or failing switch are:rn • The tool will not start when you use the switch, or it requires multiple tries to turn on, until eventually it refuses to start at all.rn • The variable speed function and electric braking aren't working properly.
... Read more
$5.95
In Stock
This is an authentic Milwaukee replacement part manufactured for use with rotary hammers. The special dust cap is used to prevent debris from entering the sleeve. This dust cap is available as an individual replacement part, please see model diagram for associative parts.
$5.95
In Stock
This 120v carbon brush is an OEM direct from the Milwaukee manufacturer. Compatible with the 5262-21 (G43B) 1" SDS D-Handle Hammer, the brush is secured to the brush holder and armature. The purpose of brushes is to conduct current in an electric motor that powers the tool. This part is sold individually. A screwdriver is needed to make the proper removal and replacement.