Cub Cadet Parts
YOUR TRUSTED CHOICE
- Genuine Brand Name Part
- Fast Delivery
- Expert Customer Support
Shop By Appliance
View MorePopular Cub Cadet Parts
$32.95
In Stock
This authentic replacement blade is manufactured for use with Craftsman walk-behind lawnmowers and is designed to deliver clean, efficient cuts. Measuring 21 inches in length, the blade features an angled design that promotes optimal airflow, allowing grass clippings to circulate through the cutting deck for effective side discharge and mulching. Over time, mower blades can dull or wear down, leading to torn grass blades and a less polished lawn appearance. Replacing a worn blade with this high-quality part ensures a sharper, cleaner cut that keeps your lawn looking its best. This blade is sold individually.
... Read more
Fixes these symptoms
- Mower blade does not cut
$5.95
In Stock
This is a genuine OEM replacement part, it is sold individually. The purpose of the 738-04124A Shear Pin is to protect your snowblower. If the auger gets jammed or clogged, the Shear Pin is designed to snap at a certain point of pressure, so it will not damage any other part of the unit.
Fixes these symptoms
- Auger will not turn
$5.95
In Stock
This is an authentic manufacturer sourced replacement cotter pin. It is a standard hardware commonly used on a variety of Craftsman lawn and garden equipment. Depending on the model of your equipment it will be used in different locations to secure two parts together. Please make sure to check appropriate diagrams for correct application for this part. This metal cotter pin is sold individually. It is best to use pliers to remove or install this part.
... Read more
Fixes these symptoms
- Auger will not turn
$43.95
In Stock
This is an authentic manufacturer-sourced replacement part which is specially designed for use with Craftsman lawn mowers. The grass bag frame supports and hold the grass bag in place, while it is collecting grass clippings. To install or replace the grass bag frame requires no tools. This part is made of metal and is sold individually.
$14.95
In Stock
This OEM fuel tank assembly is made out of Plastic and it includes the fuel lines, fuel cap, and fuel filter. It is a common part in gas trimmers that is used to hold the fuel needed for the engine. It is very important to replace the fuel tank if it is cracked or damaged to avoid further damage or serious injuries. Make sure to drain the gas tank before starting a repair.
Fixes these symptoms
- Will Not Start
$37.95
In Stock
A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below the Venturi is a butterfly valve called the throttle valve ' a rotating disc that can be turned end-on to the airflow, so as to hardly restrict the flow at all, or can be rotated so that it (almost) completely blocks the flow of air. This valve controls the flow of air through the carburetor throat and thus the quantity of air/fuel mixture the system will deliver, thereby regulating engine power and speed. The throttle is connected, usually through a cable or a mechanical linkage of rods and joints. Fuel is introduced into the air stream through small holes at the narrowest part of the Venturi and at other places where pressure will be lowered when not running on full throttle.
... Read more
Fixes these symptoms
- Engine stops after a few seconds or minutes
- Will Not Start
$33.95
In Stock
This replacement handle is a genuine OEM sourced part. It is specially manufactured for walk behind and push lawn mowers. Upper handle allows user to control the lawn mower. It is attached to the lower handle assembly that is sold separately. This part is made out of metal and is sold individually. Please note, the control bar, knobs and cables are all sold separately. You will need a wrench to replace this upper handle. • Disconnect the bail bar • Detach the control cable • Remove the bolts and the nuts that secure upper handle • Secure the new handle using the same hardware • Reattach the bar and the control cable
... Read more
$5.95
In Stock
This is a genuine manufacturer-sourced replacement hardware that is commonly utilized on Craftsman lawn and garden equipment. A lock nut is a type of nut that resists loosening when it is properly threaded onto a bolt. This is a standard hardware which has multiple applications depending on your unit, make sure to check appropriate diagrams for correct location and use of this item. Please note this durable metal lock nut is sold individually.
... Read more
$55.95
In Stock
This is a Genuine replacement Belt designed for use with Riding Lawn Tractors/Mowers. This part is made out of Rubber and it is Sold Individually. This is the the Belt that drives your unit.
Make sure to clean pulleys before installing the new belt to ensure top performance and longevity with your new belt. Inspect belt periodically and replace it when worn or stretched to maintain peak performance.
You would need a Wrench set and Pliers to replace this belt.
• For your safety make sure to disconnect the spark plug wire.
• Loosen the transaxle pulley
• Relieve tension on the upper drive belt
• Remove the upper drive belt and lawn mower belt guide
• Secure the new belt
• Reassemble and tighten the pulleys
... Read more
$13.95
In Stock
Fixes these symptoms
- Cutting line does not come out